EZ LAN Adapter for simply networking the current machines/facilities, Dual IP would be standard in Pro-face HMI
IoT has been recently promoted in Automation, but they are facing a wide range of challenges. For example, when pushing forward networking of existing facilities, end user or machine builder need to adapt the changes to the facilities, and considering to add Ethernet switches for managing mass IP addresses. It requires time and cost, therefore, the networking often have been ended up giving up.
To solve such concerns, "EZ LAN adapter" that allows you to easily achieve networking by adding it will be released. This product is a USB-Ethernet converting adapter for GP4000 Series and allows you to easily add an additional Ethernet interface (RJ-45) to HMI. That promotes networking using the existing system and reduce workload for networking and managing IP address.
Since this is an optional product, end users just attach it to the existing GP4000 Series and equipment manufacturers can add it for only the customers who need it. It’s possible to easily start IoT.
Product Features
Divide Network Layer
- Enable to divide IT network from Control network
- Total two Ethernet interfaces on HMI (Two individual IP addresses)
- Reduce workload for networking and managing IP address
Retrofit, Easily adapt existing machine/facility installed GP4000 Series
- Thanks to the EZ Series concept (Optional USB connection), you can easily add Ethernet port
Configure by only HMI
- No need to configure it by PC with software. It is easy for END user to add it.
General Specifications
| Model | PFXZCGEUUE1 |
|---|---|
| Supported standards and regulations |        |
| Supported software | GP-Pro EX Ver. 4.08 or later |
| Ethernet I/F | Modular Jack (RJ-45), IEEE802.3i/IEEE802.3u, 10BASE-T/100BASE-TX |
| USB I/F | Type A (plug), USB 2.0 High-Speed (480Mbps) |
Electrical Specifications
| Power Supply | |
|---|---|
| Rated input voltage | 5Vdc (powered from USB bus) |
| Input voltage limits | 4.75 to 5.25Vdc |
| Power consumption | 0.63W or less |
Environmental Specifications
| Physical environment | |
|---|---|
| Ambient air operating temperature | 0 to 55℃ (32 to 131 °F) |
| Storage temperature | -20 to 60℃ (-4 to 140 °F) |
| Ambient air and storage humidity | 10 to 90% RH (non condensing, wet bulb temperature 39 °C [102.2 °F] or less) |
| Dust | 0.1 mg/m3 (10-7 oz/ft3) or less (non-conductive levels) |
| Pollution degree | For use in Pollution Degree 2 environment |
| Atmospheric pressure (Operating altitude) | 800 to 1,114 hPa (2,000 m [6,561 ft] or lower) |
| Mechanical environment | |
| Vibration resistance | IEC/EN 61131-2 compliant 5 to 9 Hz Single amplitude 3.5 mm (0.14 in) 9 to 150 Hz Fixed acceleration: 9.8 m/s2 X, Y, Z directions for 10 cycles (approximately 100 minutes) |
| Concussion resistance | IEC/EN 61131-2 compliant (147 m/s2, X, Y, Z directions for 3 times) |
| Electrical environment | |
| Electrical fast transient/burst | IEC 61000-4-4 2 kV: Power port (display unit) 1 kV: Signal ports |
| Electrostatic discharge immunity | Contact Discharge Method: 6 kV Air Discharge Method: 8 kV (IEC/EN61000-4-2 Level 3) |
External Specifications
| External dimensions | W105 x H40 x D27 mm (W4.13 x H1.57 x D1.06 in.) |
|---|---|
| Cable length | 0.5 m (1.64 ft) (including connections) |
| Weight | 100 g (0.22 lb.) or less |
External Dimensions
* This product can be attached on the rear side of the display unit or to a panel other than the display unit. Refer to the installation guide for further information.